포화자화로 빨리 도달할 것이고, domain wall의 움직임이 제한된다면 큰 자기장에서 포화자화 값이 나타날 것이다. 이러한 domain wall motion을 방해하는 원인은 자기적인 힘 외에 물질 내 defects에 의해서 이다. 즉, defects가 많거나 grain이 조밀하여 grain boundary가 많다면, domain wall motion에 제약이 생긴다.
Background of Experiment
□ Al-Si Alloy
AI + Si = Al-Si Alloy
1. Low melting point
2. light
3. Large heat capacity
4. Insoluble to each other
.
.
.
Result and Analysis - EDS
□ Composition Analysis
Al, Si is almost insoluble to each other at rsoom temperature.
All solid phase will have either 100% Al phase or 100% Si phase.
ㅇ재료에서 Brittle한 특성을 결정짓는 요소
1. 온도
고온에서는 yield stress가 낮아지고 ductile fracture가 발생하는 경향이 있다. 반대 로 온도가 낮아지면 yield stress가 증가하고 brittle fracture가 발생하는 경향을 보인 다. 그 이유는 온도에 따른 원자의 진동과 관련이 있다. 원자의 진동수과 진폭은
시편의 녹는점에 가까운 온도로 가열했을 때 가루가 서로 접한 면에서 접합이 이루어지거나 일부가 증착하여 서로 연결되어 한 덩어리가 된다
BN(Boron Nitride) Spray로 시편의 표면을 코팅한다
흑연 통에 시편을 넣고 소결로에 넣는다
소결로를 닫고 진공상태로 만든 후 시편을 각각 850℃,95
grain boundary의 반사성을 grain과 다르게 하는 과정이다. 이는 grain boundary의 높은 화학적 반응성을 이용한 방법으로, grain boundary는 grain보다 부식 속도가 빨라 etching이후의 반사성에서 차이가 보인다. Grain boundary을 따라 생긴 surface groove는 사진에서 어두운 선으로 보인다.
Grain boundary와, etching에 의해 형성
따라서 재료 자체의 성능으로만 놓고 볼 때, 텅스텐과 몰리브덴, 지르코늄이 가장 우수한 재료임을 알 수 있었다. 다만 이는 재료의 고용 특성을 고려하지는 않았기 때문에 이를 고려한 평가를 적용할 경우 그 결과가 달라질 수 있다.
우선 탄화물로 석출되는 재료의 경우 grain 성장방향을 제어할 수 있
What is Amorphous metal?
Polycrystalline grains of varying shapes and sizes
Misaligned planes of atoms slip past each other easily, absorbing energy and allowing dislocations to move, making deformation permanent.
Grainboundaries represent weak spots
Also called Metallic glasses or glassy metals
Cooled faster than atoms can rearrange into a crystal.
Dislocation movement obstructed s
② Cu-45μm
① 도가니 안에 성형체 투입
② 공기 제거하고 진공 분위기 조성
③ 냉각수를 열어 과열 방지
④ 1시간 기다림
폴리싱 작업시 물을 충분히 뿌려야 마찰을 줄여 시편에 생기는 스크래치를 줄일 수 있다
현미경으로 grain의 크기, grain boundary의 형태, 기공의 정도를 관찰한다
Change of conductivity being
normal state and gas detecting in sno2 grain boundary
Amount of desorption and absorption of oxide and free electron
can control sensor sensitivity
Electrode and the electrolyte solution while maintaining a constant current from the direct oxidation and reduction when measuring current to detect the gas.
Cause ionization of the electrolyte solution, the
실험 목표
SiC 함량에 따른 Al2O3의 마찰계수의 변화와
내마모성의 변화를 토의해 본다.
SiC 함량에 따른 Al2O3의 상대밀도 변화(기공도 차이)를 확인하고 개선 방안을 토의한다.
Conclusion
* 실험결과 Ⅰ
- Grain boundary 에서 Crack의 전파 막음 → 내마모성 증가(마찰계수 감소)
- But
SiC의